Hi everyone...
A quick post about a revision I made to my modded Celestron CR-150 OTA/Lunt DSII etalon mod.
I have been wanting to set up a double stack on this system but never had a lot of time to pursue it...had been thinking of trying a Quark but wasn't prepared to shell out the cash without knowing if it would work.
What I wound up doing was hiving a local machinist make a threaded adapter to allow mw to mount the primary Etalon out of my LS80T at the rear of the donor OTA, and then install the DSII module for a DS system. I had a very short window to assemble and test yesterday over the noon hour...terrible seeing and strong winds made for an interesting first light.
The layout is shown below...from right to left: CR-150 OTA (internal Baader ERF)/Primary LS80T Etalon (red)/DSII module (black)/Moonlite focuser/B1800Ha blocking filter/Explore Scientific 3x Tele-converter/Daystar tilt adapter mounted to the ZWO ASI174MM camera:
First are a few images in the single stack mode:
In the DS mode it does improve the contrast:
Just a few points on the images...no flats (some dark banding in the DS images) and no alignment checks due to time limits. I just assembled the pieces and shot the test frames before I ran out of time. To seal the trial off I had clouds roll in until I was back to the office
Waiting on another sunny day to test things out some more.
Questions and comments are welcome...how do the modders in the group see this???
Another pending Mod is to fit the DSII to the C9.25 Edge as a single stack. A trial looked promising but my temporary housing wasn't rigid enough to stop the flexure. I'd like the ability to run this and use the pressure tuning to do quick on-band/wing images and when the seeing is good switch to the Quantum for the more narrow bandpass work (0.45A).
Thanks,
Brian
New Lunt Mod
- MapleRidge
- Way More Fun to Share It!!
- Posts: 10257
- Joined: Fri Jan 13, 2012 11:58 pm
- Location: Cambray, ON Canada
- Has thanked: 64 times
- Been thanked: 4427 times
- Contact:
New Lunt Mod
Brian Colville
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
- krakatoa1883
- Almost There...
- Posts: 1041
- Joined: Sat Jun 11, 2016 9:41 am
- Location: Mediolanum
- Has thanked: 153 times
- Been thanked: 496 times
Re: New Lunt Mod
Nice setup Brian, it seems working really fine. I don't have a DS module for my Lunt mod however my Quark increases contrast dramatically compared to the SS.
Just a question: does the ES 3x work as a telecentric amplifier ?
Just a question: does the ES 3x work as a telecentric amplifier ?
Last edited by krakatoa1883 on Fri Oct 05, 2018 7:29 pm, edited 1 time in total.
Raf
My solar images and reports with articles on solar equipment
My solar images and reports with articles on solar equipment
- MapleRidge
- Way More Fun to Share It!!
- Posts: 10257
- Joined: Fri Jan 13, 2012 11:58 pm
- Location: Cambray, ON Canada
- Has thanked: 64 times
- Been thanked: 4427 times
- Contact:
Re: New Lunt Mod
Hi Raf...
Thanks for the feedback on the setup. I hate to keep the LS80 in pieces and it does such a nice job on full disk images. I had been thinking of trying a Quark without the built in barlow as a DS unit (the photoshereic one might work ok as I'm not trying to beat the Quantum) but I don't have one to experiment with.
The ES tele-extenders are relatively telecentric...I've used them for years and seem to work as well as the Powermates. Teleview doesn't have the 3x, and these fit my budget a bit better too
Brian
Thanks for the feedback on the setup. I hate to keep the LS80 in pieces and it does such a nice job on full disk images. I had been thinking of trying a Quark without the built in barlow as a DS unit (the photoshereic one might work ok as I'm not trying to beat the Quantum) but I don't have one to experiment with.
The ES tele-extenders are relatively telecentric...I've used them for years and seem to work as well as the Powermates. Teleview doesn't have the 3x, and these fit my budget a bit better too
Brian
Brian Colville
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
- krakatoa1883
- Almost There...
- Posts: 1041
- Joined: Sat Jun 11, 2016 9:41 am
- Location: Mediolanum
- Has thanked: 153 times
- Been thanked: 496 times
Re: New Lunt Mod
Thank you for the info, I am planning to purchase a 3x amplifier because my Powermate loses amplification with the distance from the lenses. Best would be a Baader TZ system but it costs much more.
Raf
My solar images and reports with articles on solar equipment
My solar images and reports with articles on solar equipment
- MapleRidge
- Way More Fun to Share It!!
- Posts: 10257
- Joined: Fri Jan 13, 2012 11:58 pm
- Location: Cambray, ON Canada
- Has thanked: 64 times
- Been thanked: 4427 times
- Contact:
Re: New Lunt Mod
Raf...
I see that Explore Scientific has just introduced a 2"version of the 3x extender. It isn't as much an issue with the Ha system (1.25" blocking filter), but I prefer to reduce as many adapters (2"-1.25") as I can to keep the collection of optics as well aligned as I can. If it will fit ahead of the blocking filter that might help, as opposed to putting the extender between the camera and blocker.
It will be a good option to use with the WL and CaK filters since they are 2" and I could get rid of the reducers.
Brian
I see that Explore Scientific has just introduced a 2"version of the 3x extender. It isn't as much an issue with the Ha system (1.25" blocking filter), but I prefer to reduce as many adapters (2"-1.25") as I can to keep the collection of optics as well aligned as I can. If it will fit ahead of the blocking filter that might help, as opposed to putting the extender between the camera and blocker.
It will be a good option to use with the WL and CaK filters since they are 2" and I could get rid of the reducers.
Brian
Brian Colville
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
-
- Almost There...
- Posts: 636
- Joined: Mon Feb 06, 2017 9:04 pm
- Location: The Netherlands
- Been thanked: 1 time
Re: New Lunt Mod
Wow Raf, that looks great! Congratulations!
No double limb at all anymore with the DS.
No double limb at all anymore with the DS.
- Carbon60
- Way More Fun to Share It!!
- Posts: 14312
- Joined: Wed Mar 07, 2012 12:33 pm
- Location: Lancashire, UK
- Has thanked: 8558 times
- Been thanked: 8290 times
Re: New Lunt Mod
Looks like an excellent setup, Brian, producing very nice first light images, right off the bat.
I looks highly promising for the new season in spring
Stu.
I looks highly promising for the new season in spring
Stu.
H-alpha, WL and Ca II K imaging kit for various image scales.
Fluxgate Magnetometers (1s and 150s Cadence).
Radio meteor detector.
More images at http://www.flickr.com/photos/solarcarbon60/
Fluxgate Magnetometers (1s and 150s Cadence).
Radio meteor detector.
More images at http://www.flickr.com/photos/solarcarbon60/
- krakatoa1883
- Almost There...
- Posts: 1041
- Joined: Sat Jun 11, 2016 9:41 am
- Location: Mediolanum
- Has thanked: 153 times
- Been thanked: 496 times
Re: New Lunt Mod
they're Brian images, Bart
Brian, are you using the extender for extracting the focus or just to enlarge the image ? In my Lunt mod I barely reach focus with my Chameleon so I inserted a Powermate between the focuser and blocking filter.
Raf
My solar images and reports with articles on solar equipment
My solar images and reports with articles on solar equipment
- marktownley
- Librarian
- Posts: 42545
- Joined: Tue Oct 18, 2011 5:27 pm
- Location: Brierley Hills, UK
- Has thanked: 20813 times
- Been thanked: 10485 times
- Contact:
Re: New Lunt Mod
Looks like the mod works well.
http://brierleyhillsolar.blogspot.co.uk/
Solar images, a collection of all the most up to date live solar data on the web, imaging & processing tutorials - please take a look!
- MapleRidge
- Way More Fun to Share It!!
- Posts: 10257
- Joined: Fri Jan 13, 2012 11:58 pm
- Location: Cambray, ON Canada
- Has thanked: 64 times
- Been thanked: 4427 times
- Contact:
Re: New Lunt Mod
Bart, Stu, Raf, and Derek...
Thanks for all the feedback on the setup. Cloudy/rainy Thanksgiving holiday weekend has set in here, so more testes will have to wait. Maybe a nice big AR will appear next week to use as a test subject
Raf, I use the extender to bump the focal length/image scale. I also have an Airylab 2.7x telecentric to try as well, though I need to find some adapters to fit it into the system since it has all threaded connections.
Brian
Thanks for all the feedback on the setup. Cloudy/rainy Thanksgiving holiday weekend has set in here, so more testes will have to wait. Maybe a nice big AR will appear next week to use as a test subject
Raf, I use the extender to bump the focal length/image scale. I also have an Airylab 2.7x telecentric to try as well, though I need to find some adapters to fit it into the system since it has all threaded connections.
Brian
Brian Colville
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM
Maple Ridge Observatory
Cambray, ON Canada
Photos: https://www.flickr.com/photos/185395281@N08/albums
10'x15 Roll-off Roof Observatory
Takahashi EM400 Mount carrying:
C14 + Lunt 80ED
Deep Sky Work - ASI294MM Pro+EFW 7x36/Canon 60D (Ha mod), ONAG
Planetary Work - SBIG CFW10, ASI462MM
2.2m Diameter Dome
iOptron CEM70G Mount carrying:
Orion EON 130ED, f7 OTA for Day & Night Use
Ha Setup: Lunt LS80PT/LS75FHa/B1200Ha + Home Brew Lunt Double Stack/B1800Ha on the Orion OTA + Daystar Quantum
WL, G-Band & CaK Setup: Lunt Wedge & Lunt B1800CaK, Baader K-Line and Altair 2nm G-Band filter
ASI1600MM, ASI432MM, ASI294MM Pro, ASI174MM, ASI462MM