PST CaK mod

Frankenscope? Let's see it!***be advised that NOTHING in this forum has been safety tested and you are reading and using these posts at your own peril. blah, blah, blah... dont mess around with your eyesight when it comes to solar astronomy. Use appropriate filtration at all times...
Post Reply
Marsman
The Sun?
The Sun?
Posts: 4
Joined: Sat Oct 21, 2017 5:13 pm

PST CaK mod

Post by Marsman » Sun Apr 29, 2018 8:17 pm

Hi all,
I have a Coronado CaK PSt.
The 5mm blocking filter in the eye piece holder is rusted.
I want to do a mod to turn the etalon into a single unit to fit a f7 90mm refactor thus removing the penta prism.
My questions are 1. what filters do I need to replace the 5mm blocker, (Baader 1.25" Calcium K-Line Filter 395nm good ? )
2. what and where to get a front 2" adapter, PST-50 from Telescope Austria fit the etalon ? or does this not fit.
3. adapters for the rear to fit a camera to.

Most posts I have found refer to the Ha version so a comprehensive post on this mod would be appreciated.

Regards
Paul

User avatar
Bob Yoesle
Im an EXPERT!
Im an EXPERT!
Posts: 414
Joined: Thu Mar 08, 2012 7:24 pm

Re: PST CaK mod

Post by Bob Yoesle » Tue May 01, 2018 1:21 pm

Forget using the PST body and make a completely new CaK "module" using some relatively easy to obtain 2" inch adapters.

You'll need a Baader or Astronmomic Blue CCD filter for use as an ERF, and the Baader CaK filter makes a good blocking filter for the "no. 1" narrow-band component of the PST:
CaK DS Module New SM.jpg
CaK DS Module New SM.jpg (331.04 KiB) Viewed 497 times
Additional filters can be added for a narrower ERF pass-band if you go to a larger aperture, but these become more expensive.
Diagonally parked in a parallel universe.

Curiosity is the father of knowledge; uncertainty is the mother of wisdom.

Dark-Sky Defenders

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Sun May 06, 2018 12:14 am

Bob Yoesle wrote:
Tue May 01, 2018 1:21 pm
Forget using the PST body and make a completely new CaK "module" using some relatively easy to obtain 2" inch adapters..
Bob, what 2" filter adapters did you use? The CaK pst filter is not 2" and does not seem like it would be a drop in option?

Can you provide links to the actual products used that hold your dismantled PST parts?

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Sun May 06, 2018 12:17 am

I also notice in the picture you do not mention the pst #2 filter which is blue coated on yellow glass? I thought this is the actual narrowband hard coated narrow band filter? I was under the impression that the first filter in the array of the gold tube was just a sacrificial erf?

Marsman
The Sun?
The Sun?
Posts: 4
Joined: Sat Oct 21, 2017 5:13 pm

Re: PST CaK mod

Post by Marsman » Sun May 06, 2018 10:32 am

Hi Bob
This photo shows the filters in the optical train.
I have no parts that fit these threads , I guess a 2" barlow tube after the etalon would allow for the Baader filters to be fitted but I dont know what adapter to fit on the front to connect to a larger scope.
Attachments
20180506_111302.jpg
20180506_111302.jpg (2.76 MiB) Viewed 420 times

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Sun May 06, 2018 11:40 am

Your filter train is substantially different than mine. I only have the fist threaded adapter in my pst’. Dont know what that second filter holder you have is, but in my system the first filter is about 2mm seperate from the second filter and bothe in the same cell. Seperated by a single spacer ring. The last filter in your eyepiece holder is a secondary 5mm band blocker attatched to a shortpass filter.

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Sun May 06, 2018 11:42 am

Also whhat is that white adapter? Did you add that cuz its not supposed to be there. This pst is rather butchered!

Marsman
The Sun?
The Sun?
Posts: 4
Joined: Sat Oct 21, 2017 5:13 pm

Re: PST CaK mod

Post by Marsman » Thu May 10, 2018 8:43 pm

Hi, the white is tape wrapped around the etalon. The butchered bit was caused by tools to remove the eye piece holder from the focus body ( too much thread lock ).

User avatar
Merlin66
Librarian
Librarian
Posts: 3065
Joined: Tue Dec 13, 2011 1:23 pm
Location: St Leonards, Australia
Contact:

Re: PST CaK mod

Post by Merlin66 » Fri May 11, 2018 12:31 am

Check the forum library for adaptors for the PST etalon. AOK Swiss can supply.
"Astronomical Spectroscopy - The Final Frontier" - to boldly go where few amateurs have gone before
https://groups.yahoo.com/neo/groups/ast ... scopy/info
"Astronomical Spectroscopy for Amateurs" and
"Imaging Sunlight - using a digital spectroheliograph" - Springer

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 11, 2018 12:33 am

merlin: the pst cak filter is not the same as the pst ha filter. It threads on the inside of the gold tube, it is seperate from the blue ring.

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 11, 2018 12:42 am

002.jpg
002.jpg (366.4 KiB) Viewed 385 times
001.jpg
001.jpg (451.83 KiB) Viewed 385 times
003.jpg
003.jpg (365.22 KiB) Viewed 385 times

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 11, 2018 12:45 am

the gold tube thread is m50 male, and the blue ring that goes over the gold thread is m50 female.

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 11, 2018 12:50 am

the Cak filter thread is 46mm male
pstcakthread.jpg
pstcakthread.jpg (379.66 KiB) Viewed 384 times

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 11, 2018 12:55 am

merlin66 : gold tube thread at 50mm.. With this information you can make a very quick and easy attachment using off the shelf standard camera supplies. 48-52mm camera thread ring, 52mm extension barrels, 52mm to 46mm step down ring. 46-48mm nosepiece etc.
pstgoldthread50mm.jpg
pstgoldthread50mm.jpg (354.61 KiB) Viewed 384 times

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 11, 2018 1:19 am

you dont need the eyepiece holder anymore, just ditch that. All you need is the blue filter and some kind of erf system in front of it like bob states. Baader planetarium 1.25" U filter will work. The system will never be visual however so keep that in mind.

Marsman
The Sun?
The Sun?
Posts: 4
Joined: Sat Oct 21, 2017 5:13 pm

Re: PST CaK mod

Post by Marsman » Thu May 17, 2018 6:26 pm

Hi TheSkyBurner, now we are getting to the info needed to mod this thing !
So all I need to know is , what are the last filters in the eyepiece holder ?
Do I need to replace them or bin them, remember the one nearest the penta prism is rusted.

Paul

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 18, 2018 12:37 am

I would bin them and replace the whole eyepiece holder section with a 1.25" filter holder relying on a edmund optics 394nm hard coated filter.

if you wish to replace the rusted filter, find the meier optical 393nm bandpass filter ,
http://maierphotonics.com/bandpass-filter.aspx Item Number: 393BW10/12

The second filter in the eyepiece holder cannot rust, it is just a piece of dark yellow glass and you can probably clean it very well if you are careful, it is most likely some kind of standard glass based 400nm shortpass filter.

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 18, 2018 2:46 am

ill put together a parts list with links to rebuild the whole thing, just need a couple days to research more options.

User avatar
Bob Yoesle
Im an EXPERT!
Im an EXPERT!
Posts: 414
Joined: Thu Mar 08, 2012 7:24 pm

Re: PST CaK mod

Post by Bob Yoesle » Fri May 18, 2018 7:27 pm

Bob, what 2" filter adapters did you use? The CaK pst filter is not 2" and does not seem like it would be a drop in option?

Can you provide links to the actual products used that hold your dismantled PST parts I also notice in the picture you do not mention the pst #2 filter which is blue coated on yellow glass? I thought this is the actual narrowband hard coated narrow band filter? I was under the impression that the first filter in the array of the gold tube was just a sacrificial erf?
I use a standard 1.25 inch filter cell for the PST elements. I've used some scavenged parts and the Skybender unit, but will be revising this in the near future with a custom made set of components.

The only PST filter used is the "blue coated on yellow glass." Whether you call this the No. 1 or No. 2 filter is problematic, but inconsequential.
Diagonally parked in a parallel universe.

Curiosity is the father of knowledge; uncertainty is the mother of wisdom.

Dark-Sky Defenders

TheSkyBurner
Ohhhhhh My!
Ohhhhhh My!
Posts: 67
Joined: Sat May 05, 2018 7:55 pm

Re: PST CaK mod

Post by TheSkyBurner » Fri May 18, 2018 9:34 pm

Bob Yoesle wrote:
Fri May 18, 2018 7:27 pm


The only PST filter used is the "blue coated on yellow glass." Whether you call this the No. 1 or No. 2 filter is problematic, but inconsequential.
Bob, did your PST not have a filter before the blue filter? I consider the "rusted primary" filter to be filter 1, and the filter behind this to be filter 2. So it is important to an extent to separate the two, because one of them is guaranteed to suffer degradation and the other is not.
cak 2 and2b.jpg
cak 2 and2b.jpg (126.12 KiB) Viewed 115 times
cak 2 and 1.jpg
cak 2 and 1.jpg (112.38 KiB) Viewed 115 times

Post Reply

Who is online

Users browsing this forum: No registered users and 0 guests